HUATEC GROUP CORPORATION export@huatecgroup.com 86-10-82921131

HUATEC GROUP CORPORATION Şirket Profili
Ürünler
Evde > Ürünler > Ultrasonik Hata Dedektörü > Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE

Ürün Ayrıntıları

Menşe yeri: Pekin

Marka adı: HUATEC

Sertifika: ISO, CE, GOST

Model numarası: Yüksek Hızlı Tren (HFD)

Ödeme ve Nakliye Şartları

Min sipariş miktarı: 1 adet

Ambalaj bilgileri: Standart İhracat Paketi

Teslim süresi: 1-4 gün

Ödeme koşulları: T/T, PayPal, Western Union

Yetenek temini: ayda 5000 adet

En İyi Fiyatı Alın
Ürün Ayrıntıları
Vurgulamak:

ultrasonic flaw detectors

,

ultrasonic flaw detection

,

digital ultrasonic flaw detector

Frekans aralığı:
12,5KHz ila 10MKHz
İletişim dönüştürücüsü:
çeşitli eleman boyutları
Korunan yüz dönüştürücü:
film veya ayakkabı ile
Çift elemanlı dönüştürücü:
Çift eleman
Konturlu kama:
YARDIM CID AOD COD
Malzeme:
Plastik, Alüminyum, Alaşım
Frekans aralığı:
12,5KHz ila 10MKHz
İletişim dönüştürücüsü:
çeşitli eleman boyutları
Korunan yüz dönüştürücü:
film veya ayakkabı ile
Çift elemanlı dönüştürücü:
Çift eleman
Konturlu kama:
YARDIM CID AOD COD
Malzeme:
Plastik, Alüminyum, Alaşım
Ürün Tanımı

 

Ultrasonic ndt equipment Ultrasonic Inspection Equipment Probe Transducer Phased Array Prob

 

1. Straight probe: single crystal p-wave straight probe double crystal p-wave straight probe

 

2. The Angle probe: single crystal shear Angle probe a1 < aL < a Ⅱ, twin shear Angle probe

 

Single-crystal p-wave oblique probe aL

AL is a climbing wave probe near a1. The longitudinal wave transmitted along the surface of the workpiece has the advantages of fast speed, high energy, long wavelength, deeper detection depth than the surface wave, and the requirement for the surface finish of the workpiece is higher than that of the surface wave (frequency 2.5mhz wavelength about 2.4mm).

 

3. Probe with curvature: circumferential curvature, radial curvature.

 

The circumferential curvature probe is suitable for the detection of axial defects in seamless steel tubes, straight welded tubes, tubular forgings and axial workpieces. When the diameter of the workpiece is less than 2000mm, the circumferential curvature of the probe shall be ground to ensure good coupling.

 

Radial curvature probe is suitable for the detection of radial defects in seamless steel pipe, butt weld of steel pipe, barrel forging, shaft workpiece, etc. When the workpiece diameter is less than 600mm, the radial curvature of the probe should be ground to ensure good coupling.

 

4. Focusing probe: point focusing line focusing.

 

5. Surface wave probe :(when the incident Angle of the longitudinal wave is greater than or equal to the second critical Angle, the transverse wave refraction Angle is equal to 90 to form a surface wave).

 

The transverse wave transmitted along the workpiece surface has a slow speed, low energy and short wavelength, and the detection depth is shallower than the crawling wave. Therefore, the requirements for the surface finish of the workpiece are stricter than the crawling wave.

 

Surface wave detection can only detect defects at a depth of two wavelengths from the surface of the workpiece. (frequency 2.5mhz wavelength about 1.3mm).

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 0

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 1

 

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 2

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 3

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 4

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 5

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 6

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 7

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 8

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 9Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 10

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 11

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 12

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 13

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 14

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 15